The Little-Known Benefits Of Kia Picanto Key Fob Replacement
How to Replace a Kia Sportage Replacement Key
The key of a lot of Kia models has the keyless entry feature built in. This key typically resembles an electronic remote and is able to be replaced with a new one from an Kia dealer or locksmith.
Key fobs might stop working due to a variety of reasons, such as the battery being dead, worn-out buttons, signal interference or water damage. Here are some tips to help you get your Kia key fob that is a replacement for the sportage again.
How to replace a smartkey or remote key?
It doesn't matter if your Kia is equipped with an intelligent key, remote key, push to start key or a regular non-transponder steel key The battery inside these keys will eventually need replacement. This is especially relevant if your vehicle shows a message that states the remote or smart keys are in poor condition.
Fortunately, it's an easy process. To replace the battery on the keyfob remove your mechanical key from the slit at the back of the fob. Then, you need to pry the cover off. Inside the key fob, there will be a small screw that holds the battery in the correct position. Utilizing a small screwdriver take the screw off and pull out the battery that was in place. Then insert the new one and close the slit inside the key fob.
Test the key fob by pressing the lock or unlock buttons. You're in good shape If the doors lock and unlock as you expect. You can now make use of the Kia's hands-free lock/unlock feature whenever your fingers get chilly or you need to run some errands in Brandon.
Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a specific programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) don't require programming. If your keys need to be programmed again, you will need to be aware of the number written on the tag that identifies the key and keep it in a safe place.
How do you replace a battery?
If the Kia key fob doesn't respond to pressing the lock or unlock button, it is likely that the battery is low. replacing kia key fob The Keylab that is not functioning properly can cause other issues, like the check engine light flashing or the engine not turning properly. Fortunately, replacing the battery on the key fob is a relatively easy DIY project that requires just some basic tools.
Before beginning the process ensure that your vehicle is turned off and that all doors are shut. Locate the small plastic piece that is on the bottom of your key fob and gently jiggle it until the metal key is released. The key can be put into the door's driver handle to unlock your car.
To replace the battery on the key fob, you must remove the cover at the rear. Use a pry tool to loosen up the latch that holds the black negative cable. Remove the old battery, and then align the new battery in a way that the "+" positive side faces you, while the "-" negative side is facing the fob's metallic electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damage or bending the metal contacts.
Once the new battery has been installed then turn the key fob off and then turn it on in the ignition for a few times until the door locks cycle. You can then test your Kia key fob to determine whether it's functioning properly again.
How can you replace the smart key
Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The smart key is equipped with an embedded mechanical key blade however, the standard key fob does not. Both key fobs have a battery that will eventually require replacement. This is a straightforward process which takes just two minutes.
Make sure to shut off your Kia and stand on a flat well-lit and well-lit area before you begin. Also, keep in mind that there are tiny parts inside the fob that could be snagged if not cautious.
The small release button is located on the lower backside. It can be an oval silver button or a rectangular slot. After pressing this button, the mechanical key blade will come out and you can then open the key fob.
After the key fob has been opened, remove the battery. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. After you're done, your key fob should permit you to lock, unlock, and start your vehicle, even if it isn't running.
How to replace the mechanical key?
The Kia keyfob is a wonderful convenience which allows us to lock or unlock our car simply by pressing a button. Like any other device, it can have problems occasionally. There are steps that can be taken to solve these issues and keep our key fobs in good condition for the long run.
A dead or low-quality battery is one of the most frequently encountered issues. This can cause the device to stop working altogether or work intermittently. If this is the case, try replacing the battery with a new one.
If this isn't enough to resolve the problem you can try using a standard flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not to damage any internal components, or scratch the plastic. After the battery has been removed, replace it with a new one.
After the new battery has been put installed, close and unlock the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that will fit in the slot). Test the key fob to confirm it's working as intended. Contact a dealer locksmith to resolve the problem when the fob still is not working. Make sure they cut you an emergency key that works in all the trunk and door cylinders, to avoid lockouts in the future.